View FTLF1323P1BTR_4983259.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Finisar
Product Specification
OC-3 IR-1/STM S-1.1 RoHS Compliant Pluggable SFP Transceiver
FTLF1323P1xTR
PRODUCT FEATURES * * * * * * * * * * Up to 155 Mb/s bi-directional data links Hot-pluggable SFP footprint Built-in digital diagnostic functions Uncooled Fabry-Perot 1310nm laser transmitter Duplex LC connector RoHS compliant and lead-free Metal enclosure, for lower EMI Single 3.3V power supply Low power dissipation <700mW typical Industrial operating temperature range: -40C to 85C APPLICATIONS * SONET OC-3 IR-1 / SDH STM S-1.1 * SONET OC-3 SR / SDH STM I-1 * Suitable for Fast Ethernet
Finisar's FTLF1323P1xTR Small Form Factor Pluggable (SFP) transceivers are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA)1. They comply with SONET and SDH standards2 at OC-3 IR-1/STM S-1.1 and OC-3 SR/STM I-1, and are suitable for Fast Ethernet applications. Digital diagnostics functions are available via the 2-wire serial bus specified in the SFP MSA. They are RoHS compliant and lead-free per Directive 2002/95/EC3 and Finisar Application Note AN-2038. PRODUCT SELECTION
FTLF1323P1xTR
x W B Wide Extraction Bail Narrow Extraction Bail
Finisar Corporation December 2, 2005 Rev.A
Page 1
FTLF1323P1xTR Pluggable SFP Product Specification - December 2005
Finisar
I.
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Pin Descriptions
Symbol VEET TFAULT TDIS MOD_DEF(2) MOD_DEF(1) MOD_DEF(0) Rate Select LOS VEER VEER VEER RDRD+ VEER VCCR VCCT VEET TD+ TDVEET Name/Description Transmitter Ground (Common with Receiver Ground) Transmitter Fault. Not supported. Transmitter Disable. Laser output disabled on high or open. Module Definition 2. Data line for Serial ID. Module Definition 1. Clock line for Serial ID. Module Definition 0. Grounded within the module. No connection required Loss of Signal indication. Logic 0 indicates normal operation. Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Inverted DATA out. AC Coupled. Receiver Non-inverted DATA out. AC Coupled. Receiver Ground (Common with Transmitter Ground) Receiver Power Supply Transmitter Power Supply Transmitter Ground (Common with Receiver Ground) Transmitter Non-Inverted DATA in. AC Coupled. Transmitter Inverted DATA in. AC Coupled. Transmitter Ground (Common with Receiver Ground) Ref. 1 2 3 3 3 4 5 1 1 1
1
1
1
Notes: 1. Circuit ground is internally isolated from chassis ground. 2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V. 3. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.5V. MOD_DEF(0) pulls line low to indicate module is plugged in. 4. Finisar FTLF1323P1xTR transceivers operate between OC-3 and 125 Mbit/s without active control. 5. LOS is open collector output. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.5V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
VeeT 1 2 3 4 VeeT TDTXFault TD+ TX Disable VeeT MOD-DEF(2) VccT 16 15 14 13 12 11 MOD-DEF(1) VccR 6 7 8 9 10 MOD-DEF(0) VeeR Rate Select RD+ LOS RDVeeR VeeR VeeR 17 18 19 20
Towards Bezel
5
Towards ASIC
Pinout of Connector Block on Host Board
Finisar Corporation December 2, 2005 Rev.A
Page 2
FTLF1323P1xTR Pluggable SFP Product Specification - December 2005
Finisar
II.
Absolute Maximum Ratings
Symbol Vcc TS TOP RH Min -0.5 -40 -40 0 Typ Max 4.5 100 85 85 Unit V C C % Ref.
Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity
1
III.
Electrical Characteristics (TOP = -40 to 85 C, VCC = 3.10 to 3.50 Volts)
Symbol Vcc Icc Rin Vin,pp VD VEN Min 3.10 Typ 165 100 250 Vcc - 1.3 Vee 1200 Vcc Vee+ 0.8 10 400 250 800 500 VccHOST Vee+0.5 Max 3.50 300 Unit V mA mV V V s mV ps V V mVpp Ref.
Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing Transmit Disable Voltage Transmit Enable Voltage Transmit Disable Assert Time Receiver Single ended data output swing Data rise/fall time LOS Fault LOS Normal Power Supply Rejection
2
3
Vout,pp tr VLOS fault VLOS norm PSR
300 Vcc - 0.5 Vee 100
4 5 6 6 7
Notes: 1. Non condensing 2. AC coupled. 3. Or open circuit. 4. Into 100 ohm differential termination. 5. 20 - 80 % 6. Loss Of Signal is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected. 7. All transceiver specifications are compliant with a power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the power supply filtering network shown on page 23 of the Small Form-factor Pluggable (SFP) Transceiver MultiSource Agreement (MSA), September 14, 2000.
Finisar Corporation December 2, 2005 Rev.A
Page 3
FTLF1323P1xTR Pluggable SFP Product Specification - December 2005
Finisar
IV.
Optical Characteristics (TOP = -40 to 85 C, VCC = 3.10 to 3.50 Volts)
Symbol POUT ER tr/ tf RIN JTXp-p JTXrms Min -15 1261 8.2 500 -120 0.07 0.007 20% RSENS1 RSEN2 C LOSD LOSA -28 -28 1260 -45 0.5 -8 -8 1600 -28 dBm dBm nm dBm dBm dB 4 4 Typ Max -8 1360 7.7 Unit dBm nm nm dB ps dB/Hz UI UI Ref. 1
Parameter Transmitter Output Opt. Pwr: 9/125 SMF Optical Wavelength Spectral Width Optical Extinction Ratio Optical Rise/Fall Time Relative Intensity Noise Generated Jitter (peak to peak) Generated Jitter (rms) Mask Margin Receiver Average Rx Sensitivity @ OC-3 Average Rx Sensitivity @ 125 Mb/s Optical Center Wavelength LOS De-Assert LOS Assert LOS Hysteresis
2 3 3
Notes: 1. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations. 2. Unfiltered, 20-80% 3. Jitter measurements taken using Agilent OMNIBERT 718 in accordance with GR-253. 4. With worst-case extinction ratio. Measured with a PRBS 223-1 test pattern.
Finisar Corporation December 2, 2005 Rev.A
Page 4
FTLF1323P1xTR Pluggable SFP Product Specification - December 2005
Finisar
V.
General Specifications
Symbol BR BER LMAX5 Min 125 Typ Max 155 10-12 Units Ref. Mb/sec 1 2 km 4
Parameter Data Rate Bit Error Rate Max. Supported Link Length on 9/125m SMF @ OC-3
15
Notes: 1. Compliant with SONET and SDH at the following rates: OC-3 IR-1/STM S-1.1 and OC-3 SR/STM I-1. 2. Tested with a PRBS 223-1 test pattern. 3. Attenuation of 0.55 dB/km is used for the link length calculations (per GR-253 CORE). Distances are indicative only. Please refer to the Optical Specifications in Table IV to calculate a more accurate link budget based on specific conditions in your application.
VI.
Environmental Specifications
Finisar 1310nm SFP transceivers have an industrial operating temperature range from -40C to +85C case temperature.
Parameter Case Operating Temperature Storage Temperature Symbol Top Tsto Min -40 -40 Typ Max 85 100 Units C C Ref.
VII.
Regulatory Compliance
Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations. These products are certified by TUV and CSA to meet the Class 1 eye safety requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request.
Finisar Corporation December 2, 2005 Rev.A
Page 5
FTLF1323P1xTR Pluggable SFP Product Specification - December 2005
Finisar
VIII. Digital Diagnostic Functions Finisar FTLF1323P1xTR SFP transceivers support the 2-wire serial communication protocol as defined in the SFP MSA1. It is very closely related to the E2PROM defined in the GBIC standard, with the same electrical specifications. The standard SFP serial ID provides access to identification information that describes the transceiver's capabilities, standard interfaces, manufacturer, and other information. Additionally, Finisar SFP transceivers provide a unique enhanced digital diagnostic monitoring interface, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage. It also defines a sophisticated system of alarm and warning flags, which alerts end-users when particular operating parameters are outside of a factory-set normal range. The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a 2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally defined serial ID memory map remains unchanged. The interface is identical to, and is thus fully backward compatible with both the GBIC Specification and the SFP Multi Source Agreement. The complete interface is described in Finisar Application Note AN-2030: "Digital Diagnostics Monitoring Interface for SFP Optical Transceivers". The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through a 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the SFP transceiver into those segments of the E2PROM that are not write-protected. The negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. For more information, please see the SFP MSA documentation1 or Finisar Application Note AN-2030. Digital diagnostics for the FTLF1323P1xTR are externally calibrated by default. Please note that evaluation board FDB-1018 is available with Finisar ModDEMO software that allows simple to use communication over the 2-wire serial interface.
Finisar Corporation December 2, 2005 Rev.A
Page 6
FTLF1323P1xTR Pluggable SFP Product Specification - December 2005
Finisar
IX.
Mechanical Specifications
Finisar's Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA) 3.
FTLF1323P1BTR
Finisar Corporation December 2, 2005 Rev.A
Page 7
FTLF1323P1xTR Pluggable SFP Product Specification - December 2005
Finisar
FTLF1323P1WTR
Finisar Corporation December 2, 2005 Rev.A
Page 8
FTLF1323P1xTR Pluggable SFP Product Specification - December 2005
Finisar
X.
PCB Layout and Bezel Recommendations
Finisar Corporation December 2, 2005 Rev.A
Page 9
FTLF1323P1xTR Pluggable SFP Product Specification - December 2005
Finisar
Finisar Corporation December 2, 2005 Rev.A
Page 10
FTLF1323P1xTR Pluggable SFP Product Specification - December 2005
Finisar
XI. 1. 2. 3.
References Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 2000. Documentation is currently available at Finisar upon request. Bellcore GR-253 and ITU-T G.957 Specifications. Directive 2002/95/EC of the European Council Parliament and of the Council, "on the restriction of the use of certain hazardous substances in electrical and electronic equipment." January 27, 2003.
XII.
For More Information
Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com
Finisar Corporation December 2, 2005 Rev.A
Page 11

▲Up To Search▲

Price & Availability of FTLF1323P1BTR

	To Download FTLF1323P1BTR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .